epaper_nametag/cable_cap.scad

// Waveshare 2.13" e-Paper HAT (B) — ESP32 Nametag Case
// Display slides in from X+; FPC cable exits freely out the open X+ side
$fn = $preview ? 32 : 64;

// --- Display Dimensions (landscape: portrait rotated 90°) ---
DISP_W = 59.20;   // overall width  (X) — portrait height
DISP_D = 29.20;   // overall depth  (Y) — portrait width
DISP_T = 1.0;     // thickness      (Z)

// --- Active (Visible) Area ---
ACT_W  = 48.55;   // active area width (X) — portrait AA height
ACT_D  = 23.71;   // active area depth (Y) — portrait AA width

// Border offsets from display edge to active area:
//   X-: portrait top border  ≈ 1.95 mm  (closed/backstop side)
//   X+: portrait FPC border  ≈ 8.70 mm  (open/entry side)
//   Y±: symmetric            ≈ 2.75 mm  each side
ACT_X_OFFSET = 1.95;
ACT_Y_OFFSET = 2.75;

// --- FPC Cable (exits X+ side) ---
FPC_W   = 12.5;
FPC_T   = 0.3;
FPC_LEN = 20.0;   // visualization length of hanging tail

// --- FPC Return Pocket ---
FPC_FLOOR_DROP  = 0.75;  // extra depth below display cavity floor
FPC_POCKET_LEN  = 20.0;  // how far in from X+ face the pocket extends
FPC_POCKET_PAD  = 2.0;   // padding on each side of FPC cable width

// --- Case Parameters ---
WALL       = 3.0;   // must exceed MAG_LIP_H (2.0) to keep pocket floor
LIP        = 1.5;   // front bezel lip thickness (Z)
TOL        = 0.3;   // per-side display clearance
CHAM       = 1.0;
CHAM_ANGLE = 60;
CORNER_R   = 2.5;
CLIP_Z     = 0;     // preview: mm to remove from Z+ (0 = full model)
CLIP_Y     = 0;     // preview: mm to remove from Y+ (0 = full model)
SHOW_DISP  = true;
SCREEN_EXPLODE    = 0;     // mm to pull display toward X+ in preview

// --- Output ---
PART = "all";  // "all" = preview scene; "case" = case STL at origin; "cap" = cap STL at origin

// --- Slip-Fit Cap (X+ end) ---
SHOW_CAP    = true;   // show cap in preview
CAP_RIBS    = false;  // include retention ribs in cap
CAP_DETENT  = true;   // include snap detent nubs and dimples
DETENT_R    = 0.5;    // detent nub/dimple radius (mm); tune across prints
CAP_PAD     = 4.0;   // Min cap bore depth
CAP_ENGAGE  = CAP_PAD + 6.0;   // sleeve engagement length over case exterior (X)
CAP_WALL    = 1.5;   // sleeve and end-wall thickness
CAP_TOL     = 0.2;   // per-side slip clearance between bore and case exterior
CAP_BEVEL   = 1.0;   // chamfer size on X+ face edges to guide cap onto case
CAP_EXPLODE = CAP_PAD + 10;     // preview: mm to pull cap away from case in X+ (0 = seated)

// --- Magnetic Strip Locating Lip (rear face) ---
MAG_L        = 1.772 * 25.4;   // strip length ≈ 45.01 mm
MAG_W        = 0.512 * 25.4;   // strip width  ≈ 13.00 mm
MAG_LIP_H    = 2.0;            // lip height protruding from rear face
MAG_LIP_WALL = 1.0;            // lip wall thickness
MAG_TOL      = 0.2;            // per-side clearance for strip fit

// --- Derived Dimensions ---
cav_w  = DISP_W + TOL * 2;
cav_d  = DISP_D + TOL * 2;
case_w = WALL + DISP_W + (TOL * 1.5);         // ends at display X+ face; cap retains display
case_h = WALL + DISP_T + LIP;
case_d = WALL * 2 + cav_d;

_cham_xy = CHAM * tan(CHAM_ANGLE);

win_x = WALL + TOL + ACT_X_OFFSET;
win_y = WALL + TOL + ACT_Y_OFFSET;

// FPC return pocket geometry (X+ face)
fpc_pkt_y  = WALL + TOL + (DISP_D - FPC_W) / 2 - FPC_POCKET_PAD;
fpc_pkt_yw = FPC_W + 2 * FPC_POCKET_PAD;

// Cap derived
_cap_bore_w  = case_d - 2*CAP_WALL;                // bore Y width (fits recessed case)
_cap_bore_h  = case_h + CAP_TOL;                   // bore Z height (CAP_TOL clearance on each Z face)
_cap_gap_w   = (case_w - CAP_ENGAGE + CAP_PAD) - (win_x + ACT_W + _cham_xy); // gap between cap X- face and beveled bezel X+ end
_detent_x    = (CAP_ENGAGE - CAP_PAD) / 2; // detent offset from cap X- face; same in cap local and case global offset
_detent_z    = (CAP_WALL + CAP_TOL + case_h) / 2; // Z center of recessed engagement face
// Magnetic strip recess geometry (centered on back face)
_lip_il = MAG_L + 2 * MAG_TOL;
_lip_iw = MAG_W + 2 * MAG_TOL;
_lip_x  = case_w / 2 - _lip_il / 2;
_lip_y  = case_d / 2 - _lip_iw / 2;

// -------------------------------------------------------------------
// Display mockup — approximate geometry for preview only
// -------------------------------------------------------------------
module EPD213B() {
    color([0.82, 0.84, 0.80])
        cube([DISP_W, DISP_D, DISP_T]);
    color("white")
        translate([ACT_X_OFFSET, ACT_Y_OFFSET, DISP_T])
            cube([ACT_W, ACT_D, 0.02]);
    color([1.0, 0.85, 0.1])
        translate([DISP_W, (DISP_D - FPC_W) / 2, (DISP_T - FPC_T) / 2])
            cube([FPC_LEN, FPC_W, FPC_T]);
}

// -------------------------------------------------------------------

module rounded_box(l, w, h, r) {
    hull()
        for (dx = [r, l-r], dy = [r, w-r])
            translate([dx, dy, 0]) cylinder(r=r, h=h, $fn=32);
}

module epd_case() {
    difference() {
        rounded_box(case_w, case_d, case_h, CORNER_R);

        // Display cavity — extends 0.01 mm past X+ face to leave that side open
        translate([WALL, WALL, WALL])
            cube([cav_w + 0.01, cav_d, DISP_T + TOL]);

        // Active area window + chamfered top edges
        translate([win_x, win_y, WALL + DISP_T - 0.01])
            cube([ACT_W, ACT_D, LIP - CHAM + 0.02]);
        hull() {
            translate([win_x, win_y, case_h - CHAM])
                cube([ACT_W, ACT_D, 0.01]);
            translate([win_x - _cham_xy, win_y - _cham_xy, case_h])
                cube([ACT_W + 2*_cham_xy, ACT_D + 2*_cham_xy, 0.01]);
        }

        // FPC return pocket — drops floor of display cavity near X+ face
        translate([case_w - FPC_POCKET_LEN, fpc_pkt_y, WALL - FPC_FLOOR_DROP - 0.01])
            cube([FPC_POCKET_LEN + 0.02, fpc_pkt_yw, DISP_T + TOL + FPC_FLOOR_DROP + 0.01]);

        // Magnetic strip recess in back face
        translate([_lip_x, _lip_y, -0.01])
            cube([_lip_il, _lip_iw, MAG_LIP_H + 0.01]);

        // Cap wall recess — step in z- face at X+ end so cap sits flush
        translate([case_w - CAP_ENGAGE + CAP_PAD, -0.01, -0.01])
            cube([CAP_ENGAGE + 0.02 - CAP_PAD, case_d + 0.02, CAP_WALL + CAP_TOL + 0.01]);

        // Detent dimples on Y± faces — accept cap nubs when fully seated
        if (CAP_DETENT)
            for (dy = [CAP_WALL + CAP_TOL, case_d - CAP_WALL - CAP_TOL])
                translate([case_w - CAP_ENGAGE + CAP_PAD + _detent_x, dy, _detent_z])
                    sphere(r=DETENT_R);

        // Cap wall recess — step in y- face at X+ end so cap sits flush
        translate([case_w - CAP_ENGAGE + CAP_PAD, -0.01, -0.01])
            cube([CAP_ENGAGE - CAP_PAD + 0.02, CAP_WALL + CAP_TOL + 0.01, case_h + 0.02]);

        // Cap wall recess — step in y+ face at X+ end so cap sits flush
        translate([case_w - CAP_ENGAGE + CAP_PAD, case_d - CAP_WALL - CAP_TOL, -0.01])
            cube([CAP_ENGAGE - CAP_PAD + 0.02, CAP_WALL + CAP_TOL + 0.01, case_h + 0.02]);

        // Bevel all 4 exterior edges of X+ face — guides cap onto case during installation
        // Y± faces are recessed by (CAP_WALL + CAP_TOL); Z- face is recessed by CAP_WALL
        translate([0, 0, -0.01])
            linear_extrude(case_h + 0.02)
                polygon([[case_w - CAP_BEVEL, CAP_WALL + CAP_TOL - 0.01],
                         [case_w + 0.01, CAP_WALL + CAP_TOL - 0.01],
                         [case_w + 0.01, CAP_WALL + CAP_TOL + CAP_BEVEL]]);
        translate([0, 0, -0.01])
            linear_extrude(case_h + 0.02)
                polygon([[case_w - CAP_BEVEL, case_d - CAP_WALL - CAP_TOL + 0.01],
                         [case_w + 0.01, case_d - CAP_WALL - CAP_TOL + 0.01],
                         [case_w + 0.01, case_d - CAP_WALL - CAP_TOL - CAP_BEVEL]]);
        translate([0, case_d + 0.01, 0])
            rotate([90, 0, 0])
                linear_extrude(case_d + 0.02)
                    polygon([[case_w - CAP_BEVEL, CAP_WALL - 0.01],
                             [case_w + 0.01, CAP_WALL - 0.01],
                             [case_w + 0.01, CAP_WALL + CAP_BEVEL]]);
        translate([0, case_d + 0.01, 0])
            rotate([90, 0, 0])
                linear_extrude(case_d + 0.02)
                    polygon([[case_w - CAP_BEVEL, case_h + 0.01],
                             [case_w + 0.01, case_h + 0.01],
                             [case_w + 0.01, case_h - CAP_BEVEL]]);
    }
}

// -------------------------------------------------------------------
// Slip-fit cap — slides over X+ end of case; FPC exits through end-wall slot
// -------------------------------------------------------------------
module cable_cap() {
    _bore_h  = _cap_bore_h - CAP_WALL;
    _bore_r  = _bore_h / 2;
    _cap_h   = _cap_bore_h + CAP_WALL;
    _cap_cy  = (_cap_bore_w + 2 * CAP_WALL) / 2;  // Y center of cap

    union() {
    difference() {
        // Outer shell: flat rectangle at open end, rounded rectangle at closed end
        hull() {
            cube([0.01, _cap_bore_w + 2 * CAP_WALL, _cap_bore_h + CAP_WALL]);

            for (dy = [CORNER_R, _cap_bore_w + 2*CAP_WALL - CORNER_R])
                translate([CAP_ENGAGE + CAP_WALL - CORNER_R, dy, 0])
                    cylinder(r=CORNER_R, h=_cap_bore_h + CAP_WALL);
        }

        // Rounded bore
        translate([-0.01, CAP_WALL, CAP_WALL])
            cube([CAP_ENGAGE - _bore_r + 0.01, _cap_bore_w, _bore_h]);
        translate([CAP_ENGAGE - _bore_r, _cap_bore_w, _cap_bore_h - _bore_r])
            rotate([90,0,0])
                cylinder(h=_cap_bore_w - CAP_WALL, r=_bore_r);
    }

    // Retention ribs — flush with X- face, full cap height, 2×2 mm, just outside FPC pocket
    if (CAP_RIBS)
        for (rib_dy = [fpc_pkt_y - CAP_WALL, fpc_pkt_y + fpc_pkt_yw])
            translate([CAP_ENGAGE - CAP_PAD, rib_dy, 0])
                cube([CAP_WALL, CAP_WALL, _cap_h]);

    // Detent nubs on Y± bore walls — snap into case dimples when fully seated
    if (CAP_DETENT)
        for (ny = [CAP_WALL, case_d - CAP_WALL])
            translate([_detent_x, ny, _detent_z])
                sphere(r=DETENT_R);

    // Chamfer tab: extends window bezel chamfer across the gap to the cap X- face
    hull() {
        translate([-_cap_gap_w, 0, _cap_bore_h])
            cube([_cap_gap_w, case_d, 0.01]);
        translate([-0.01, 0, _cap_bore_h + CAP_WALL - 0.01])
            cube([0.01, case_d, 0.01]);
    }
    }
}

_clip = [case_w + 1,
         ($preview && CLIP_Y > 0) ? max(0.01, case_d - CLIP_Y) : case_d + 1,
         ($preview && CLIP_Z > 0) ? max(0.01, case_h - CLIP_Z) : case_h + 1];

if (PART == "case") {
    epd_case();
} else if (PART == "cap") {
    cable_cap();
} else {
    color("#004B49")
        intersection() { epd_case(); cube(_clip); }

    if ($preview && SHOW_DISP)
        translate([WALL + TOL + SCREEN_EXPLODE, WALL + TOL, WALL])
            EPD213B();

    if (SHOW_CAP)
        color("#1A3A6B")
            translate([case_w - CAP_ENGAGE + CAP_EXPLODE, 0, 0])
                intersection() {
                    cable_cap();
                    translate([0, 0, -(CAP_TOL + CAP_WALL)])
                        cube([CAP_ENGAGE + CAP_WALL + 1,
                              _clip[1],
                              case_h + 2*(CAP_TOL + CAP_WALL) + 1]);
                }
}