epaper_door_case/lid.scad

// Sliding lid for EE04 case — integrates epd_case as ceiling
// z=0 = bottom of flanges; ceiling at z=LID_T (epd_case backplate) or z=FLANGE_H (flat test plate)
include <params.scad>
use <epd_case.scad>
use <GDEY0583T81.scad>
use <fpc_adapter.scad>

/* [Preview] */
SHOW_DISP = true;

/* [FPC Adapter Mount] */
ADAPT_SLOT_GAP = 10.0;  // gap: adapter Y+ edge to slot Y- edge ← tune

// Adapter board dimensions (must match fpc_adapter.scad PCB_W / PCB_H)
_adpt_w = 32.0;
_adpt_h = 18.0;

// Derived adapter position in lid XY space
_slot_y    = LID_Y_LEN - 3 - FPC_U_DEPTH + FPC_U_T;  // slot Y- edge
_adapt_ox  = PCB_OX + FPC_CX - _adpt_w / 2;           // adapter PCB X- edge
_adapt_oy  = _slot_y - ADAPT_SLOT_GAP - _adpt_h;       // adapter PCB Y- edge

// ============================================================
//  LID  (slide-on; enters from Y- face, closes toward Y+)
//  Flanges sit inside cavity and ride on base retention flange hypotenuses.
// ============================================================
module lid() {
  // Flanges: right triangles in XZ; hypotenuse at reciprocal angle to base retention flanges.
  // Wide vertical face at x=WALL+FLANGE_W (inner), tip at bottom-wall-face — same
  // (-FLANGE_W, -FLANGE_H) hypotenuse slope as base flanges so they mate when lid slides in.
  color("#2C3863") {
    // Left (X-) flange
    hull() {
      translate([WALL + FLANGE_W - SLIDE_CLEAR - 0.01, 0, 0])
        cube([0.01, LID_Y_LEN - FLANGE_W + SLIDE_CLEAR, FLANGE_H - SLIDE_CLEAR]);
      translate([WALL + SLIDE_CLEAR, 0, -0.005])
        cube([0.01, LID_Y_LEN - FLANGE_W + SLIDE_CLEAR, 0.01]);
    }
    // Right (X+) flange
    hull() {
      translate([OUT_L - WALL - FLANGE_W + SLIDE_CLEAR, 0, 0])
        cube([0.01, LID_Y_LEN - FLANGE_W + SLIDE_CLEAR, FLANGE_H - SLIDE_CLEAR]);
      translate([OUT_L - WALL - SLIDE_CLEAR - 0.01, 0, -0.005])
        cube([0.01, LID_Y_LEN - FLANGE_W + SLIDE_CLEAR, 0.01]);
    }

    // Interior ribs — 2 mm wide
    translate([WALL + FLANGE_W - SLIDE_CLEAR, 0, 0])
      cube([2.0, LID_Y_LEN - FLANGE_W + SLIDE_CLEAR, FLANGE_H]);
    translate([OUT_L - WALL - FLANGE_W + SLIDE_CLEAR - 2.0, 0, 0])
      cube([2.0, LID_Y_LEN - FLANGE_W + SLIDE_CLEAR, FLANGE_H]);

    // Y+ locking flanges — angled wedge matching side-flange profile; split around FPC notch
    for (seg = [
      [FLANGE_W - SLIDE_CLEAR + 2.0,
       2+PCB_OX + FPC_CX - FPC_NOTCH_W/2 - (WALL + FLANGE_W - SLIDE_CLEAR + 2.0)],
      [PCB_OX + FPC_CX + FPC_NOTCH_W/2,
       OUT_L - FLANGE_W + SLIDE_CLEAR - 2.0 - (PCB_OX + FPC_CX + FPC_NOTCH_W/2)]
    ]) {
      hull() {
        translate([seg[0], LID_Y_LEN - FLANGE_W + SLIDE_CLEAR - 0.01, 0])
          cube([seg[1], 0.01, FLANGE_H - SLIDE_CLEAR]);
        translate([seg[0], LID_Y_LEN - SLIDE_CLEAR - 0.01, -0.005])
          cube([seg[1], 0.01, 0.01]);
      }
      // Backing rib — 2 mm deep on cavity face of flange, matches side-rib style
      translate([seg[0], LID_Y_LEN - FLANGE_W + SLIDE_CLEAR - 2.0, 0])
        cube([seg[1], 2.0, FLANGE_H]);
    }

    // Y+ corners — intersection of the X-prism and Y-prism in the corner region.
    // Equivalent to: cube with the X-flange relief cut AND the Y-flange relief cut applied.
    // Result tapers to zero height along both wall faces, producing a single shared edge.
    // Left corner (X-)
    intersection() {
      hull() {
        translate([WALL + FLANGE_W - SLIDE_CLEAR - 0.01, LID_Y_LEN - FLANGE_W + SLIDE_CLEAR, 0])
          cube([0.01, FLANGE_W - 2*SLIDE_CLEAR, FLANGE_H - SLIDE_CLEAR]);
        translate([WALL + SLIDE_CLEAR, LID_Y_LEN - FLANGE_W + SLIDE_CLEAR, -0.005])
          cube([0.01, FLANGE_W - 2*SLIDE_CLEAR, 0.01]);
      }
      hull() {
        translate([WALL + SLIDE_CLEAR, LID_Y_LEN - FLANGE_W + SLIDE_CLEAR, 0])
          cube([FLANGE_W - 2*SLIDE_CLEAR, 0.01, FLANGE_H - SLIDE_CLEAR]);
        translate([WALL + SLIDE_CLEAR, LID_Y_LEN - SLIDE_CLEAR - 0.01, -0.005])
          cube([FLANGE_W - 2*SLIDE_CLEAR, 0.01, 0.01]);
      }
    }
    // Right corner (X+)
    intersection() {
      hull() {
        translate([OUT_L - WALL - FLANGE_W + SLIDE_CLEAR, LID_Y_LEN - FLANGE_W + SLIDE_CLEAR, 0])
          cube([0.01, FLANGE_W - 2*SLIDE_CLEAR, FLANGE_H - SLIDE_CLEAR]);
        translate([OUT_L - WALL - SLIDE_CLEAR - 0.01, LID_Y_LEN - FLANGE_W + SLIDE_CLEAR, -0.005])
          cube([0.01, FLANGE_W - 2*SLIDE_CLEAR, 0.01]);
      }
      hull() {
        translate([OUT_L - WALL - FLANGE_W + SLIDE_CLEAR, LID_Y_LEN - FLANGE_W + SLIDE_CLEAR, 0])
          cube([FLANGE_W - 2*SLIDE_CLEAR, 0.01, FLANGE_H - SLIDE_CLEAR]);
        translate([OUT_L - WALL - FLANGE_W + SLIDE_CLEAR, LID_Y_LEN - SLIDE_CLEAR - 0.01, -0.005])
          cube([FLANGE_W - 2*SLIDE_CLEAR, 0.01, 0.01]);
      }
    }
  }

  difference() {
    union() {
      // Flat ceiling plate for EPD_ANGLE > 0
      color("#004B49")
      translate([0, -WALL, FLANGE_H])
        rounded_box(OUT_L, OUT_W, LID_T, CORNER_R);
      if (EPD_IS_LID)
        translate([OUT_L/2 - epd_case_w/2, OUT_W - WALL, LID_T + WALL])
          rotate([-EPD_ANGLE, 0, 0])
            translate([0, -epd_case_d, 0])
              epd_case();

      // Y- lip — same rounded_box profile clipped to the Y- wall zone so the
      // lip corners match the base exterior corners
      color("#004B49")
      intersection() {
        translate([0, -WALL, FLANGE_H - LIP_H - SLIDE_CLEAR])
          rounded_box(OUT_L, OUT_W, LIP_H + SLIDE_CLEAR, CORNER_R);
        translate([-0.1, -WALL - 0.1, FLANGE_H - LIP_H - SLIDE_CLEAR - 0.1])
          cube([OUT_L + 0.2, WALL + 0.2, LIP_H + SLIDE_CLEAR + 0.2]);
      }
    }

    // FPC cable slot — through flat ceiling plate (test-fit lid only; EPD_IS_LID uses epd_case slot)
    translate([PCB_OX + FPC_CX - FPC_NOTCH_W/2,
               LID_Y_LEN - 3 - FPC_U_DEPTH + FPC_U_T,
               FLANGE_H - 0.1])
      cube([FPC_NOTCH_W, FPC_SLOT_W, LID_T + 0.2]);
  }
}

// ============================================================
//  RENDER
// ============================================================
lid();